Kathrein CAP 910 Operations Instructions

MobiSet 4 digitalCAP 910- English -Translation of the original operating manual

10• Circular cutter, Ø 38 mm• Flat-bladed screwdriver for M5 screws• Power drill• Galvanised round head screws, depending on the roof structure (Ø:

11• When selecting the installation position, take into account the range of movement of the turntable (see the grey shaded area in the graphics). Wi

12• In the centre of the intended position of the turntable, drill the opening for the cable gland with a circular cutter (Ø: 38 mm). Deburr the hole

13• For very thin roof panel materials and insuffi cient support in the insulating material, through holes (Ø: 5.5 mm) into the interior of the vehicl

14• Before starting adhesive work, note that the optimum processing temperature of materials to be glued and the sealant is between +15 °C and +25 °C

15Figure: E1INSTALLATION AND CONNECTIONFigure: E2Master coaxial cable(marked red)• Lift up the turntable and place it carefully on the mounting plate

16INSTALLATION AND CONNECTIONVERSION WITH EXTERNAL CABLE GLAND (FIG. F)• Lay the cables supplied with the turntable (2 x coaxial cables and 1 x power

17INSTALLATION AND CONNECTIONInitially tighten the coaxial cable plugs fi nger-tight, using no tools, then tighten them lightly using an open-ended SW

18INSTALLATION AND CONNECTIONINSTALLATION OF THE UFS 940SWThe four screw sockets provided (see diagram on the next page) allow you to install the rece

19INSTALLATION AND CONNECTIONRemoving the blanking plugs:When the unit is delivered, the screw sockets are covered with blanking plugs. These can be p

2GENERALCOMPANY ADDRESS AND ACCREDITED REPRESENTATIVEKATHREIN-Werke KGAnton-Kathrein-Straße 1 - 3P.O. Box 100 44483022 Rosenheim GERMANYProf. Dr. Dr.

20Using the adhesive strips supplied, now install the infra-red sensor either on the receiver or at the chosen location. If the infra-red sensor is in

21Useful information for installing the receiver on a TV set:For installation by attachment to the rear of a TV set, securing with two screws is suffi

22INSTALLATION AND CONNECTIONSecure the receiver at the installation location previously selected and prepared.Do not force it, and take care that not

23INSTALLATION AND CONNECTION• Lay the master coaxial cable (marked red) to the UFS 940sw and the second coaxial cable to the second receiver. If you

24INSTALLATION AND CONNECTIONUnder certain circumstances, problems can arise when the units are connected to different connecting sockets or circuits/

25Important:For operation with two batteries, it must be ensured that the ignition signal earth has the same potential as the power supply battery ear

26RECEPTION RANGE / FOOTPRINTThe footprint is the reception area on the earth that a satellite covers with its transmission beam (spot), within which

27If repairs to the system or individual components are necessary, contact your specialist dealer or our service centre (see below for address).Never

28If a defect arises in the electronic controls, after some disassembly work the antenna can be returned to the park position (horizontal position) ma

29MANUAL LOWERING TO PARK POSITIONMANUAL LOWERING1. In the centre of the axis (arrowed) there are two plastic caps, one to the left and one to the ri

3MOBISET 4 CAP 910 COMPONENTS / SCOPE OF DELIVERY75 cm satellite dishTwin LNBTurntable with integral controls and GPS receiverUFS 940sw(Front view)The

30TECHNICAL SPECIFICATIONSType CAP 910Order no. 20310022LNB2 switchable outputs: V/H (14/18 V), low/high (0/22 kHz)LNB supply voltage V vertical: 11.5

31SIKAFLEX® 291 SAFETY DATA SHEET1. Materials/preparation and company designationData on the product (trade name): Sikafl ex® 291Data on manufacture

325. Measures for fi re fi ghtingSuitable extinguishing media Compatible with all extinguishing media in general use.Special hazard from the product,

334.4‘ methylene-diphenyl-diisocyanate 101-68-8 Permissible workplace concentration 0.05 mg/m3 TRGS 900/DE/2004 101-68-8 Permissible workplace co

3411. Toxicology dataSensitisation Sensitisation/allergic reactions may occur. Sensitive individuals may exhibit allergic reactions even at very low

35Risk phrases42 Sensitisation possible by breathing in.Safety phrases23 Do not breathe in gas/smoke/vapour/aerosol.45 In the event of accide

36SIKAFLEX® 291 TECHNICAL DATA SHEETSikaflex®-291 1 / 2Technisches MerkblattVersion 12 / 2005Sikaflex®-291Der haftstarke Marine-DichtstoffTechnische E

37SIKAFLEX® 291 TECHNICAL DATA SHEETSikaflex®-291 2 / 2Weitere Informationen Internet: www.sika-industry.de, E-Mail: [email protected]

38CAP 910 OPERATING MANUALThe operating manual for the CAP 910The automatic overnight updating of the EPG data described in the UFS 940sw operating ma

39All settings on the UFS 940 are made using the remote!IMPORTANT INFORMATION FOR CAP 910 BEFORE SETUPREMOTE CONTROLSo as to avoid overheating the tur

4GENERAL ... 2MOBISET 4

40FIRST INSTALLATIONBefore using your unit for the fi rst time, read the “Safety Instructions - Important Information” and “Installation and Connection

41The following display appears:Press the  (green) button to move to the next menu.Use the  buttons to select whether to replace the factory pre-pr

42FIRST INSTALLATIONSystemUse the  buttons here at “System” to select “CAP”. Then use the  buttons to select the “Initialize CAP” line and press t

43FIRST INSTALLATIONLocal time offset (UTC)Here you can use the  buttons to select the local time offset to UTC (formerly GMT) (e.g. for Germany: +

44CAP MENU (TURNTABLE ANTENNA SETTINGS)Press the  (green) button. The following display appears:Use the  buttons to select the “Antenna Confi gurati

45This function should be used only by experienced users. Exact knowledge of the satellite position and your present location are necessary when align

46CAP MENU (TURNTABLE ANTENNA SETTINGS)Using the  buttons or the numeric keys, enter the required tilt angle (skew) for the LNB and press the  butt

47This menu allows important basic settings for the CAP, such as the elevation border or elevation offset to be set. These two settings in particular

48CAP MENU (TURNTABLE ANTENNA SETTINGS)Set the “Countdown for search start” on the display shown to the right. Use the  buttons to set the countdown

49If the vehicle is not on supports during the search process and people are moving around inside it, there is a risk that movement of the vehicle wil

5CONTENTS (OPERATING MANUAL)CAP 910 OPERATING MANUAL ...

50CHANNEL (SATELLITE) SELECTION/PROGRAMMING THE TIMERProviding you are not in a menu, pressing the  button calls up the channel list. The following d

51TIMER PROGRAMMINGTo prevent the turntable rotating at a time when it is unsupervised or when rotation might be irritating (e.g. in the middle of the

52After a change of location, the antenna moves to the last position selected. After initialisation, you will therefore see the following display (exa

53As soon as the turntable has found the correct satellite, it saves this position. During this process you receive no TV picture. The turntable will

54You have four options for “parking” the antenna.1. The antenna can be moved to park position by pressing the  button twice.2. Press the  (green)

55SPECIAL MESSAGES FROM THE TURNTABLEThe following messages are shown on the screen to protect your reception system and the on-board power supply:SYS

56The vehicle ignition was switched on. For safety reasons, the turntable moves into the park position. This operates however only if the green igniti

57SPECIAL MESSAGES FROM THE TURNTABLEA serious software error has occurred. Reset the turntable in the CAP menu, or contact our service centre. MESSAG

58SPECIAL MESSAGES FROM THE TURNTABLEThe satellite you have selected cannot be received from your current location, or there may have been changes mad

59DECLARATION OF CONFORMITY

6PROPER USEThe MobiSet 4 digital CAP 910 is designed to receive digital TV and radio channels via satellite. The automatic positioner is intended to b

DISPOSAL INSTRUCTIONSInternet: http://www.kathrein.deKATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P.O. Box 100 444 • 83004 Rosenheim GERMANY936.368

7SAFETY INSTRUCTIONS - IMPORTANT NOTESSafety during installation workWhen carrying out installation work in locations where there is a risk of falling

8Road Traffi c Licensing Regulations (StVZO)The applicable regulations of the StVZO must be observed in respect of fi xed installation of the turntable

9SAFETY INSTRUCTIONS - IMPORTANT NOTESChecks before commencing a journey• Before commencing a journey, the antenna must always be lowered into horizo